CDA Oven SA116 User Manual

SA116 Single Oven  
Manual for Installation, Use and Maintenance  
Customer Care Department • The  
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY  
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu  
 
Important  
Read the user instructions carefully before using the oven for the first time.  
Follow the instructions for first use of the oven.  
Clean the oven regularly.  
Remove spills as soon as they occur.  
Always use oven gloves when removing shelves and trays from the ovens.  
Do not allow children near the oven when in use.  
Do not allow fat or oils to build up on the oven shelves, grill pan or oven base.  
Do not place any cooking utensils or plates directly on the oven base.  
Always grill with the oven door closed.  
Do not grill food containing fat without using the grill pan grid.  
Do not cover the grill pan grid or the oven walls with aluminium foil.  
Do not use the oven tray for roasting.  
Do not perform maintenance or cleaning of the oven without first switching off the electricity supply. If the oven has  
recently been used, allow to cool.  
Do not place hot enamel parts in water. Leave them to cool first.  
Do not allow vinegar, coffee, milk, saltwater, lemon or tomato juice to remain in contact with enamel parts.  
Do not use abrasive cleaners or powders that will scratch the surface of the enamel.  
Do not attempt to repair the internal workings of your oven.  
 
First use of the oven  
First use  
Before using the oven for the first time we recommend that you clean the oven with soapy water, rinse carefully and  
then heat on each of the below programmes at maximum temperature for the specified time. A slightly unpleasant  
smell may be produced, caused by grease remaining on the oven elements from the production process.  
60 minutes conventional oven.  
15 minutes grill.  
Please note:  
This oven has been fitted with a cooling fan to achieve maximum efficiency and to maintain low surface  
temperatures. The cooling fan will switch on automatically when the oven is switched on and switch off  
automatically when the oven is switched off.  
The oven light remains on for every cooking function.  
 
Oven controls & use  
Cooking function knob  
To set the function, turn the cooking function knob clockwise to the required function.  
Each of the oven functions uses different elements within the oven to offer you the best choice of cooking every time. These  
are explained below:  
Conventional Oven  
O
This function uses the top and bottom heating elements with a temperature between 50 C and Max.  
Natural convection creates a perfect cooking zone in the centre of the oven.  
Lower element  
O
This function uses the bottom heating element with a temperature between 50 C and Max.  
This function is ideal for cooking foods that require a greater heat underneath.  
Upper element  
O
This function uses the upper heating element with a temperature between 50 C and Max.  
This function is ideal for cooking foods that require a greater heat above.  
Grill  
This function radiates the heat from the grill element.  
O
The grill must be set at 200 C.  
Please note:  
Always grill with the oven door closed.  
Put the grill pan as close to the grill as possible.  
Do not grill for more than 30 minutes at a time.  
Preheat the grill for approximately five minutes with the oven door closed.  
Temperature knob  
To set the temperature, turn the temperature knob clockwise to the required temperature.  
Once the oven has reached the required temperature, the temperature indicator lamp on the control panel  
will switch off.  
The temperature indicator lamp will light up when the oven elements are working.  
 
Changing the Oven Lamp  
Before any maintenance is started involving electrical parts, the appliance must be disconnected from the  
power supply.  
If the oven has been in use, let the oven cavity and the heating elements cool down before attempting  
any maintenance.  
Changing the bulb (fig. 1)  
Unscrew the protective cover.  
Unscrew and replace the bulb with the new one suitable for high temperatures (300oC) having the following  
specifications: 230-240V 50Hz, 15W, E14.  
Refit the protective cover.  
fig. 1  
IMPORTANT: Never use screwdrivers or other utensils to remove the light cover. This could damage the  
enamel of the oven or the lamp holder. Remove only by hand.  
Please note:  
The bulb replacement is not covered by your guarantee.  
 
Cleaning and Maintenance -  
Removing the Oven Door  
The oven doors can easily be removed as follows:  
Open the door fully.  
Open the lever on the left and right hinges (as show in figure 2).  
Gently close the door until left and right hinge levers are hooked to the door.  
Lift the door by removing the hinge hooks from their location in the direction indicated.  
Rest the door on a soft surface.  
To replace the door, repeat the above steps in reverse order.  
fig. 2  
 
Cleaning and Maintenance -  
Removing the Oven Door Inner Glass  
To remove the inner pane of the top oven door on both sides  
1. Remove the oven door as shown below.  
2. Release the two upper blocks by pressing down as shown in fig. 3.  
3. Slide the door glass out in the direction shown in fig. 3.1.  
4. Clean the glass with an appropriate cleaner, dry thoroughly and place on a soft surface.  
5. Now you can also clean the inside of the outer glass.  
To replace the inner glass  
1. Ensuring the OK symbol on the glass is facing you, slide the glass back into the frame.  
2. Replace the upper blocks, ensuring they lock back into place.  
3. Replace the oven door.  
IMPORTANT: Do not clean the glass whilst it is still hot.  
Please keep the ok symbol to the bottom right of the oven door (fig. 3.1).  
fig. 3  
fig. 3.1  
 
Installation  
Important  
If the oven is being installed into a built under oven housing unit ensure that the front rail at the top of the unit is not  
installed as it could restrict ventilation.  
Ensure that air can flow freely around the housing area. If the oven is being installed into a fully enclosed built-under oven  
housing unit it may be necessary to cut a small slot in the top of the plinth fitted under the unit. Cut a section 400mm wide  
and a minimum of 15mm high to allow air to pass under the unit. Alternatively cut a section 400 x450mm in the base of  
the carcass as indicated.  
Failure to allow adequate ventilation to the appliance may result in overheating or damage to adjacent units and could  
invalidate the warranty.  
This appliance is type X installation.  
The walls of the kitchen units must be able to withstand temperatures of 75oC above ambient (typically this is between  
90oC and 100oC).  
When correctly installed ensure that there is a gap of 4mm minimum between the sides of the oven and adjacent  
furniture doors.  
Lift the oven carefully into position on the shelf, taking care NOT to lift it by the door handle. If you lower the oven door, you  
will see 4 screw holes, 2 on each side of the oven. The oven should then be secured to the housing by fitting screws into these  
holes. Remember the housing should not be free standing but be secured to the wall and/or adjacent fittings.  
How to install your oven  
You will need the following housing area fit your  
oven correctly.  
450  
100  
Dimensions  
Height (mm)  
Width (mm)  
Depth (mm)  
Oven  
598  
Housing  
575  
5
5
8
598  
560  
515  
560 (min)  
594  
560  
560  
The oven is designed to fit into a cabinet of 600mm  
width. The oven can be built in or built under  
the kitchen units, but you must ensure that it is  
properly ventilated. In the diagram the built-in oven  
is ventilated by means of a space at the top of the  
kitchen cabinet. There are many other methods of  
ventilating your oven - Consult a qualified engineer  
for advice.  
499  
20-24  
400  
560  
450  
560  
fig. 4  
 
Electricity supply to your oven  
Warning! this appliance must be earthed.  
This appliance must be connected by a competent person, using fixed wiring via a double pole switched fused spur outlet.  
We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will  
comply with the I.E.E and local regulations. The wires in the mains lead are coloured in accordance with the following code:  
GREEN AND YELLOW = EARTH BLUE = NEUTRAL BROWN = LIVE.  
As the colours of the wires in the mains lead for the appliance, may not correspond with the coloured markings identifying  
the terminals in your spur box, proceed as follows:  
1. The wire which is coloured green and yellow must be connected to the terminal marked E (Earth) or  
coloured Green.  
2. The wire which is coloured blue must be connected to the terminal marked N (Neutral), or coloured Black.  
3. The wire which is coloured brown must be connected to the terminal marked L (Live), or coloured Red.  
DOUBLE POLE SWITCHED  
FUSE SPUR OUTLET  
USE A 13 AMP FUSE  
 
Notes :  
 
To contact our Customer Care Department, or for Service,  
please contact us on the details below.  
Customer Care Department • The  
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY  
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu  
 

Belkin Network Card F5D6230 3 User Manual
Bertazzoni Cooktop PM6040X User Manual
Black Box Network Card 21834 User Manual
Braun Electric Toothbrush D12013 W User Manual
Brocade Communications Systems Security Camera 53 1003373 01 User Manual
Bush Hog Compact Loader 2427 User Manual
Casio Projector XJH1600 User Manual
Cateye Bicycle EC 3600 User Manual
Cecilware Fondue Maker CM 24 User Manual
Christie Digital Systems Projector 38 VIV402 01 User Manual